Home Improvement Stack Exchange
Home Improvement Stack Exchange

Questions tagged [framing-fasteners]

19 questions
5
votes
2 answers

Steel Stud Galvanic Isolation

I am building a light-gauge steel frame workshop that is made from 0.55mm cold-formed 90mm x 45mm (2"x4") light-gauge steel studs. The structure is wrapped in 25mm (1") of extruded polystyrene (XPS) insulation and then 12mm (1/2") plywood cladding…
Eric
  • 396
  • 1
  • 8
3
votes
1 answer

Are Construction Screws equivalent to a framing nails?

I am not asking for opinions or what is better than the other. I am looking for literature with data that shows the specifications and guidance on how to compare them with each other on a performance level (not cost). I hope I am using the…
Turtle Turtle
  • 247
  • 1
  • 5
  • 15
2
votes
1 answer

Jackless window framing: How common is it?

The Pacific Northwest National Laboratory recommends to use a very stripped down framing method for windows & doors; namely: eliminate the jack stud and hang the header board using tie plates, and reduce drastically the number of cripple studs under…
Michaël
  • 121
  • 4
2
votes
1 answer

How to remove wood framing from concrete floor

I remodelling my cabin and removing a closet. The wood framing seems to be glued(?) to the concrete floor. What's the proper way to remove the framing? Best idea I've got is a big crowbar but I wonder if I'll damage the concrete. Is there any magic…
Jeffrey
  • 2,021
  • 1
  • 18
  • 34
2
votes
1 answer

Framing a basement column with off-center 2x6s?

I'm going to frame a column in my basement, but I need it to include a few outlet boxes (one for power, and one for speaker). All the videos I've watched show 2x4s being ramset into the columns dead center. That makes sense, but I need room for the…
Dave
  • 455
  • 2
  • 9
  • 18
2
votes
3 answers

Should I use glue or powder-actuated nails when framing over gypcrete?

I have a current gypcrete-over-radiant-over-foamboard-over-slab floor in my unfinished basement. I'm about to frame it out to finish it. I've already located all the tubing, and I do have spots where I can nail or screw most of the walls down. Three…
Carey Kloss
  • 45
  • 5
2
votes
2 answers

Is there a test to determine if a nail is galvanized or not?

I bought a nailer which came with some old nails that I'm going to use for a shed floor into pressure treated wood. As you can see, they kinda look galvanized. They have that grey patina. But other than just looking at them, is there anything else…
brentonstrine
  • 1,000
  • 3
  • 15
  • 33
1
vote
0 answers

Floor and Marriage Joint question

Found a leak in our second floor bathroom which destroyed the existing OSB subfloor and had to remove - giving me the opportunity to remodel it into a more modern master bath (fun). Discovered what appears to be two issues that needs to be…
bcee987
  • 11
  • 1
1
vote
0 answers

Can I anchor to the edges of sistered studs?

This seems like a very basic question but googling it just gives me articles on how to join two pieces of wood—I know how to do that. My question is, if I sister up a stud next to another one and screw it down tight, how strong is a screw that…
MinimumSense
  • 11
  • 1
1
vote
4 answers

Box on sill construction: fastening the floor to the foundation wall

How exactly is the header fastened to the sill plate in box-on-sill construction using 2x dimensioned lumber?
mr blint
  • 1,142
  • 13
  • 29
1
vote
2 answers

How long screws for attaching sill plate to concrete foundation?

I need to attach a sill plate to a foundation that does not have anchor bolts. I'd like to use GRK Caliburn screws. The sill plate is 1.5 inches thick. How long should the screws be? It looks like 2-3/4" is a commonly sold length. Is that…
Vebjorn Ljosa
  • 9,575
  • 18
  • 58
  • 86
1
vote
1 answer

Do 8d nails come in different lengths?

From what I can tell, 8 Penny nails are 2 1/2" long. Charts on the internet back this up. But I was looking at the nailing guide for this hurricane tie on homedepot.com and it specifies two different 8d nail lengths. A search on Home Depot does…
brentonstrine
  • 1,000
  • 3
  • 15
  • 33
0
votes
2 answers

Framing a separating wall using tie plates

I am working on replacing a separating wall between my garage and basement. It is separating only, not load bearing. There are three main sections: plain wall floor to ceiling. plain wall floor to lower than ceiling (keeping 2" away from HVAC ducts…
negacao
  • 805
  • 1
  • 7
  • 19
0
votes
2 answers

Effective fastening methods for attaching French cleats to OSB

I have metal studs 24" O.C. covered with 7/16" OSB. I want to attach French cleats to the walls, and I can land a set of screws into a stud every 2 feet, but I'd also like to put in some fasteners between the studs as well. Is there a standard…
roasthead
  • 492
  • 3
  • 14
0
votes
0 answers

Fastening material for panelling an old plaster wall

I have a 100-year-old garage made of yellow bricks and with plastered walls inside. The paint and the plaster on the walls are chipping due to humidity and age. A part of the walls has been covered with OSB panels (18mm thickness, 690x2440mm size…
retrography
  • 123
  • 1
  • 1
  • 5
1
2